Jet Ski Lifts and Jet Ski Parts

PWC Jet Ski Lifts - ELectric stand Mount

For docks that don’t have pilings that extend above the deck (they have been cut off flush with the deck), our Model 2000 PWC Jet Ski Electric Stand Mount Lift comes with a custom built stand that reinforces and acts as an above dock piling, giving the PWC & Jet Ski Lift track something strong to bolt to. The stand is aluminum but you can custom order a steel stand.

These lifts come with an aluminum track that provides either 5 or 7 feet of travel range. 5 feet is recommended for places where the water level stays consistent. 7 feet is recommended for places that have tides.

Often installed with a Gem remote or PWC Jet Ski Walkaround Platform.

Need a minimum of 2 feet of water to work

PWC Jet Ski Lift - Electric Piling MOunt

Perfect For docks with vertical pilings above the deck surface. Our model 2000 PWC & Jet Ski Lift is designed to bolt directly to a piling and is fully motorized.

These lifts come with an aluminum track that provides either 5 or 7 feet of travel range. 5 feet is recommended for places where the water level stays consistent. 7 is recommended feet for places that have tides.

Often installed with a Gem remote and PWC Jet Ski Walk around Platform.

Need a minimum of 2 feet of water to work

Platfrom

We carry these platforms in stock

12”x 6’ walkboard
12”x 12’ walkboard
24”x 12’ walkboard

All other platforms are custom and available upon request

3000 Doozie Twin Jet Ski Lift

3,000lb weight capacity
Hot Dip Galvanized
Designed to lift boat from from above, under roof
Lifts come complete (except wood)
- Pipe, steel (2 slotted beams and 4 cradles), parts, cable, and hardware
- Spring loaded up/down switch for safety
- 2-piece motor/drive cover
- Carpet for bunks (the wood)
- 8 cable covers
Side mounted drive
Lift range 10' - lift speed approximately 3.5 ft/minComes with
Operates as two independent lifts in one boat slip

4000 Doozie Deluxe Double PWc Jet Ski Lift

Our Boat House Deluxe PWC Jet Ski Lifts can be used for owners who have a slip in their boat house dedicated for one or two of their Jet Skis or PWC's. Our Doozie Deluxe double jet ski lift has two sets of bunks. Wood for the bunks are set at two different heights so one jet ski can be taken out while the other stays securely on the lift.

This lift will help ensure safety, cleanliness as well as longevity of your jet ski's & PWC's.

Also available with overhead beams on the side mount or center mount lifts

Capacities:

4,000lb weight limit

Hot Dip Galvanized
Designed to lift boat from above, under roof
Lifts come complete (except wood)
- Pipe, steel, parts, cable, and hardware
- Spring loaded up/down switch for safety
- 2-piece motor/drive cover
- Carpet for bunks (the wood)
Side mounted drive for easy maintenance
Lift range 10' - lift speed approximately 3.5 ft/min
Single Side Mounted Motor
Optional Remote Control

Bunk Install Diagram example

4000 Overhead Side Mount Double Jet Ski

By adding upper beams to your boat house, you are allowing installation flexibility providing leeway in where the lifting points are located.

4,000lb weight capacity
Hot Dip Galvanized
Designed to lift boat from above, under roof
Lifts come complete (except wood)
- Pipe, steel, parts, cable, and hardware
- Spring loaded up/down switch for safety
- 2-piece motor/drive cover
- Carpet for bunks (the wood)
Side mounted drive
Lift range 10' - lift speed approximately 3.5 ft/min
The Boat House Overhead Side Mount Boat Lifts are available with 9' or 10' cradles. Cradles are the bottom beam.

Bunk Install Diagram example

Doozie Jet Ski Walk Around 3 Sides

Our PWC Jet Ski Walk Around Platforms are making life easier.

These all aluminum frame platforms mount directly to your lift, allowing for easy access while trying to mount, clean, or fuel your ski.

The platforms are designed with Thru-Flo decking to ensure a nice, safe, slip free feel.

The long side of the platform is 12 feet. The short side is 4 feet. The walk path is a foot wide.

Here are the install instruction and a video

Doozie Jet Ski Walk Around 4 Sides

Our PWC Jet Ski Walk Around Platforms are making life easier.

These all aluminum frame platforms mount directly to your lift, allowing for easy access while trying to mount, clean, or fuel your ski.

The platforms are designed with Thru-Flo decking to ensure a nice, safe, slip free feel.

The long side of the platform is 12 feet. The short side is 4 feet. The side closest to the dock is two five feet sections. The walk path is a foot wide.

Here are the install instructions part 1, part 2 and a video

1000 - 2000 Doozie Jet Ski Upgrade

This kit converts a 1000lb jet ski lift to a 2000 jet ski lift.

Includes arms, rollers, bunk brackets, and hardware. Hardware includes:

(8) 3/16 Nuts
(4) U-Bolts

The arms are longer than the 1000lb Jet Ski lift and allows room for a walk around to be attached. The rollers are stronger allowing more weight. With new arms comes new bunk brackets and hardware for attaching them.

Doozie Jet Ski Walkboard upgrade 2 piece 5’ w/hardware

If you already have a 3-sided walkaround and would like to make it a 4-sided walkaround, this upgrade kit is what you are looking for! It comes with:

2 - 5 foot walkaround pieces
List hardware here

Jet ski Dock Stand

This aluminum stand allows Jet Ski lifts to attach to the flat part of the boat dock. We recommend that its used with a Jet Ski Stand Angle and place above a piling. We do not recommend placing Jet Ski lifts on walkways as the weight of the Jet Ski can make the dock lean. This dock stand is the only difference between the stand and piling jet ski lift options. Steel stand can be custom ordered at customers request.

Jet Ski Stand Angle

This Jet Ski stand angle goes underneath the Jet Ski stand to help support it to the dock. It does not come with hardware

Jet Ski Arms

Jet Ski arms that attach to the Jet Ski carriage. The are 72” x 4”. These allow for 3 and 4-sided walkarounds to be added to the lift. They also allow for wider PWC to be picked up on the lift.

Jet Ski 5’ or 7’ track

Jet Ski tracks come in 5 or 7 feet of travel. They come in aluminum or you can order a custom steel track. We can also customize the length of the track it you need it to be longer. We recommend 5’ tracks in places with consistence water levels (like lakes) and 7’ in areas with frequent water level changes (like rivers and coastal area). Make sure the electricity running to the lift is properly grounded otherwise it can cause the track to prematurely rust.

Jet Ski Drive

The Jet Ski Drive allows for the lift to be operated with electricity. It comes with a 2” pulley, an 8” pulley, a 28” belt, a switch, and a 110V GFI cord. This drive does NOT allow for a 220V upgrade.

Jet Ski Hobie Cat Adapter

Made for a 16ft Hobie Cat

Has 4 rollers, 2 for each catamaran

Attaches to the 2000lb Jet Ski Stand or Piling

LOCK AND PIN

This lock and pin is part of your jet ski stand or piling lift. It will hold your jet ski to the track and release the weight on the cable.

Here is a video on how to use it.

Jet Ski Drive Cover W/Hardware

Cover for Jet Ski motor. Comes with (4) 5/16 x 1/2 self tapping screws

2000Lb Jet Ski roller

There are four of these black rollers in the 5 and 7 foot JetSki track.

550 Jet Ski roller kit

These are replacement rollers for the old Doozie Jet Ski Lift with a weigh capacity of 550. It comes with (4) 7/8” and (2) 1” rollers

1” Doozie 550 Jet Ski Pulley Roller

Sold individually

7/8” Doozie 550 Jet Ski Roller7/8”

Sold individually

Jet Ski Bunk Brackets set of 4

Jet Ski bunk brackets come in a set of 4. We can also sell them separately. They attach to the arms with the included hardware and hold the wooden or aluminum bunks. The hardware includes …

Adjustable double jet ski brackets

These brackets are used to hold two jet skis on one boat lift with 9 or 10 foot cradles. These can be used on our boathouse and 4-post lifts. These adjustable brackets mount straight onto your cradle (the steel beam). The tall ones are 17 inches and you will put two 2x6x10 pieces of wood on them if your cradles are 8 feet apart. 2x6x8 if your cradles are 6 feet apart. The small ones are 4 inches and you will also put 2x6x10 or 2x6x8. We do not sell the wood but we do sell the carpet for the wood in 12 inch strips. Most brackets are set 24 inches apart for standard Jet ski lift installs. 2x6x8 if your cradles are 6 feet apart. Not all the hardware is shown in the picture. Each bolt bag has 4 plates, 4 bolts, and 4 nuts.

Jet Ski Carriage

The jet ski carriage is the body of the Jet Ski lift. It holds the arms and runs up and down the track. The blue pulley with grease fittings is included

JET SKi Carriage Shaft roller

This carriage shaft goes in the Jet Ski carriage and holds the rollers in the Jet Ski track.

Aluminum Jet Ski Bunks

Aluminum bunks are a great investment. They never need to be replace (unlike the standard wooden bunks) and never rust. They are sturdy and don’t bow. A 4” rubber pad prevents any harmful rubbing against the bottom of the boat. This aluminum jet ski bunks are perfect if you live on salty waters. The cradles are 4” x 6’ and have a riser upgrade if you plan on using a walkaround. They are often upgraded at the time of purchase along with aluminum cradles.